Smart-Clip original is one of the best unlock clip in worldwide market. We have a problem to find correct category in our shop to match it possibilites since it's right now only Clip but soon JTAG for Motorola phones will be addedd (free of charge) and then you can repair phones with lost boot zone, repair phones using full flashing or test CPU/RAM/FLASH. Right now it's for sure in Clip category since it's multifunctional device that it's FULLY UPDATABLE FREE OF CHARGE for support new models of C3xx, Exxx and Vxxx. Name "Smart..." also fits to this product perfectly - it's very smart since you can upgrade it in real-time using ActiveX via webbrowser in just a seconds - you connect Clip via special LPT cable with computer and then run a webpage (special component will automatically checks newest SW version and if available upgrade your Clip to support newest phones). No PC, disassembling or special technical knowledge needed just connect cable to phone and press RED button.

New version of Smart-Clip firmware 2.25 and SmartMoto v1.20
This update adds a models V235, L2

Unlock in few seconds
Flashing, change language possible
Realtime upgrade, fast support from producer


Currently supported phone models:

Sendo cell phones

* Sendo snd2xx
* Sendo snd3xx (incl. snd360 s360)
* Sendo snd5xx (incl. snd570 m570)
* Sendo snd6xx (incl. snd600 p600/s600)
* Sendo snd8xx

Motorola ACER platform cell phones

* Motorola C115 (incl. v.1.0.50)
* Motorola C116
* Motorola C117
* Motorola C118
* Motorola C155
* Motorola C156
* Motorola C157
* Motorola E365
* Motorola V170
* Motorola V171

Motorola P2K platform (flash and unlock)

* Motorola A630
* Motorola A830
* Motorola A835
* Motorola A845
* Motorola A920
* Motorola A925
* Motorola A1000
* Motorola C236
* Motorola C250
* Motorola C260
* Motorola C266
* Motorola C268
* Motorola C330
* Motorola C331
* Motorola C332
* Motorola C333
* Motorola C334
* Motorola C335
* Motorola C336
* Motorola C350
* Motorola C350L (incl. R312ULS_G_09.10.2CR)
* Motorola C350V
* Motorola C353
* Motorola C355V
* Motorola C359V 
* Motorola C370
* Motorola C380
* Motorola C385
* Motorola C390
* Motorola C450
* Motorola C450L
* Motorola C550
* Motorola C650
* Motorola C651
* Motorola C975
* Motorola C980
* Motorola E1
* Motorola E1000
* Motorola E370
* Motorola E375
* Motorola E378i
* Motorola E380
* Motorola E770
* Motorola E396
* Motorola E398
* Motorola E550
* Motorola E920
* Motorola L2
* Motorola L6
* Motorola L7
* Motorola M1000
* Motorola T280
* Motorola T280i
* Motorola T720 (incl. T720_G_05_08_81R)
* Motorola T720i
* Motorola T721
* Motorola T722i
* Motorola T725e
* Motorola U6
* Motorola V3 (incl. R374_G_0E.40.74R, R374_G_0E.40.96R)
* Motorola V3i
* Motorola V3r
* Motorola V3x
* Motorola V60
* Motorola V60i
* Motorola V66
* Motorola V66i
* Motorola V70
* Motorola V80 (incl. R37_G_0E.03.26R)
* Motorola V150 (incl. R313LT_G_09.20.05R)
* Motorola V151
* Motorola V180 (incl. R364_G_0B.D1.1CR)
* Motorola V186
* Motorola V188
* Motorola V190
* Motorola V220 (incl. R365_G_0B.D2.0.FR, R364_G_0B.D1.1FR)
* Motorola V226
* Motorola V235
* Motorola V300
* Motorola V303
* Motorola V330 (R472_xx)
* Motorola V360
* Motorola V360v
* Motorola V400
* Motorola V500
* Motorola V505
* Motorola V525
* Motorola V525M
* Motorola V535
* Motorola V547 (incl. R472_xx)
* Motorola V545
* Motorola V550
* Motorola V551 (incl. R472_xx)
* Motorola V600
* Motorola V620
* Motorola V635 (ver R474_G_08.48.6CR)
* Motorola V975 (ver R245_xxx)
* Motorola V980
* Motorola V1050 

Update process of Smart Clip:

It`s online process, just connect Smart-Clip to PC and open Smart-Clip website, then go to upgrade page and press connect, after this Update and that is all!

Step by step:
1. Connect Smart-Clip to PC using LPT cable
2. Power Smart-Clip ON (warning: don't use battery!)
3. Go to our Upgrade Zone
4. Upgrade Zone uses ActiveX element, answer "Yes" to install and run it
5. Press "Connect"
6. Press "Update" if your version is out of date
7. Power Smart-Clip OFF
8. Disconnect LPT cable

Operating with Smart-Clip:

Operation instruction

1. Power on the Smart-Clip and E/G indicator will light green.
2. Power on the phone without SIM card and flash card (if present).
3. Connect phone to Smart-Clip and press the "Unlock" button ( red on older clips ).
4. E/G indicator will light green and go off, the phone will switch off (some models will automatically turn on then).
5. E/G will light green on success or red on error
6. Successful unlock resets User Code to 1234, Security Code to 000000


Sendo snd2xx/snd3xx/snd5xx/snd6xx/snd8xx unlocking procedure

1. Power off the phone
2. Connect clip to the phone using RJ45 cable (pinouts below)
3. Press UNLOCK button
4. Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. RX/TX leds will blink
5. E/G led will glow green on success.

When you unlock Sendo phone use either fully charged phone battery OR power supply from Smart-Clip. Don't use them both at the same time! If you use power supply from Smart-Clip, make sure current is not less than 300mA, otherwise not all data will be properly recorded to the phone.


Motorola V1050, V975 (ver R245_xxx) (inc. boot 0.6.1.2) and others Motorola models with boot 0.6.3.1

You need to use SmartMoto to unlock these models.
1. Power on the phone.
2. Connect it to PC via smart-clip, detect your phone in SmartMoto.
3. Go to Unlock bookmark, pick your model, press "Remove RSA" button.
4. Phone goes into boot mode, reserve copy of security area is created.
5. Part of phone Firmware is reflashed.
6. Phone doesn't power on after that. SmartMoto will give you the message requiring to take phone into boot mode using keys combination: *,#, PWR ON (at this moment the phone has to be connected by usb cable) or using Repairing cable.
7. Press "OK" button. Wait till the process ends.
8. The phone powers on and is ready to be unlocked by Smart-Clip using simple "press one button" method (press Unlock button on Smart-Clip).


Unlock procedure for Motorola A920/A925/A1000

1. Power the phone on.
2. Connect the phone to a powered clip. Phone display should give "USB cable connected" message.
3. Press UNLOCK button on the clip.
4. Phone reloads. Within 5-10 seconds phone display gives "Waiting for PST" message.
5. Press A and B keys simultaneously in upper part of the handset. The phone enters boot mode (if you don't press these 2 keys during "Waiting for PST" message, the clip will give red E/G led and you will have to start with step 1 again).
6. After A and B keys have been pressed E/G green led will blink and phone reboots. Meanwhile E/G will give frequent green blinking and phone will turn on.
Do not disconnect cell phone from Smart-Clip while green led indicator blinks!
7. Green E/G led glows. The cell phone is unlocked.


Motorola C115/C116/C117/C155/C156/E365/V170/V171 unlocking procedure

1. Power off the phone
2. Connect clip to the phone using RJ45 cable (pinouts below)
3. Press UNLOCK button
4. Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. RX/TX leds will blink
5. E/G led will glow green on success *

* After successful unlock (green led on) phones with inserted sim card may ask for PCK or NCK code. Enter 00000000 ("zero" 8 times)
 

Now new feature available, flashing software added






Specification:

Weight: 310 g